Sleeves, spacers and hex standoffs are the parts nobody thinks about until the assembly does not fit. A standoff 0.1 mm too long throws off a whole stack of boards; a spacer whose across-flats dimension is wrong cannot be held with a wrench; a sleeve whose bore is too tight will not slide onto its shaft. These are small parts with an outsized effect on assembly. This post shows you how to specify each one — which dimension is critical for its type, how the stack-up adds up, and what to state for each threaded end.

What each part does
A sleeve is a hollow turned tube, usually round, that fits over a shaft or a rod. It can act as a bushing, a spacer, or a guide. A spacer is a part whose job is to hold two things a fixed distance apart — its critical dimension is its length. A hex standoff is a spacer with a hexagonal body and threaded ends, male or female or both, used to mount circuit boards, panels, and assemblies with a wrench. Precimora’s sleeves and spacers page lists custom brass hex standoffs and threaded spacers for OEM assemblies, and notes that across-flats dimension, overall length, internal and external thread configuration, material grade, and finish are reviewed against the approved drawing.
The distinctions matter because they decide which dimensions are critical. For a sleeve, the bore and the outside diameter decide whether it fits. For a spacer, the length decides whether the assembly stacks up. For a hex standoff, the across-flats dimension decides whether a wrench can hold it, and the thread configuration decides how it connects. A drawing that treats all three as “a turned tube” will miss the dimension that matters for the part in question.
The dimensions that decide the fit
For a sleeve, the bore (inside diameter) and the outside diameter are the functional dimensions, and they are usually the tightest. Precimora’s sleeves page states the general tolerance is typically ±0.05 mm, with ±0.02 mm achievable on critical diameters on request, and that concentricity is typically 0.02 mm. For a sleeve that must slide on a shaft, the bore tolerance and the shaft tolerance together decide the fit — a sliding fit is typically H7/g6 or H7/h6 to ISO 286, as stated on the bushings page. State the fit, not just the bore size, so the supplier can confirm the pair.
For a spacer, the length is the critical dimension, and Precimora states length tolerance is typically ±0.05 mm. That sounds small, but in a stack of several spacers the tolerances add up. Five spacers, each ±0.05 mm, can stack to ±0.25 mm of variation in the assembly — enough to misalign a board or a panel. If the assembly stacks several spacers, state the stack-up requirement, not just the individual length tolerance, and ask the supplier whether a tighter length tolerance on each spacer is needed. The drawing governs, and the stack-up is the buyer’s responsibility to state.
For a hex standoff, the across-flats (A/F) dimension is the one that decides whether a standard wrench fits. Across-flats is the distance between two opposite flat faces of the hexagon, and it should match a standard wrench size — a standoff with an A/F of 7 mm takes a 7 mm wrench; an A/F of 6.8 mm takes nothing properly. State the A/F as a standard size, and state the thread configuration: male thread on one end and female on the other, female on both ends, or male on both ends. Each configuration assembles differently, and the wrong one cannot be fixed after the part is made.
Threads: male, female, and both
A standoff’s threads are its connection, and they need the same care as any other thread. Precimora’s sleeves page states the standard plainly: plain bore as standard, internal thread 6H or external thread 6g on request, metric to ISO 261, and UNC/UNF inch threads on request. State the thread on each end separately — a standoff can have an M3 female thread on one end and an M3 male thread on the other, and the drawing must say so for each end.
Thread depth matters more on standoffs than on most parts, because the threaded length is short and the engagement decides the strength. A female thread that is too shallow will strip under torque; a male thread that is too short will not engage enough of the mating thread. State the thread depth for each end, and the torque the joint must survive, so the supplier can confirm the engagement is enough. The companion post on specifying threads covers the full callout — diameter, pitch, class, and depth — and it applies here in full.

Material and finish: the same rules, smaller parts
Sleeves and spacers are made in brass, stainless steel, carbon steel, and aluminum, according to Precimora’s product page, and the material choice follows the same logic as for any turned part: brass for machinability and corrosion resistance in mild environments, stainless steel where strength or corrosion resistance matters, aluminum where weight matters, carbon steel where cost matters and corrosion is controlled.
The finish follows the same rules too. As-machined Ra 0.8–1.6 µm is the standard, polished Ra 0.4 µm or better is available on request, and nickel, tin, or zinc plating (nickel typically 5–25 µm), chromate passivation, or clear lacquer are options confirmed from the drawing. For a standoff that will be handled during assembly, a plated or lacquered finish resists tarnish and looks better; for a hidden spacer, as-machined is enough. State the finish per part, not per order, because a visible standoff and a hidden spacer in the same assembly need different finishes.
How to state a sleeve, spacer, or standoff in your RFQ
A good RFQ for these parts states the type, the critical dimension, and the assembly it belongs to. For a sleeve: bore, outside diameter, length, and the fit it must achieve. For a spacer: length, the stack-up requirement, and the bore or thread it must clear. For a hex standoff: across-flats dimension, overall length, thread configuration on each end, and the torque the joint must survive.
Also state the quantity and the assembly context. Standoffs and spacers are usually ordered in quantities that match an assembly run, and the supplier needs to know whether the parts will be used one at a time or in stacks. If the parts are part of a kit, say so — the packaging and labelling should match the kit, and that is agreed before production, not after delivery.
Buyer questions, answered
What is the critical dimension for each type?
For a sleeve, the bore and outside diameter — they decide whether it fits. For a spacer, the length — it decides whether the assembly stacks up. For a hex standoff, the across-flats dimension — it decides whether a wrench can hold it — plus the thread configuration on each end.
My spacers are all within tolerance, but the assembly still misaligns — why?
Because tolerances add up in a stack. Five spacers, each ±0.05 mm, can stack to ±0.25 mm of variation — enough to misalign a board or a panel. State the stack-up requirement for the assembly, not just the individual length tolerance, and ask the supplier whether a tighter length tolerance on each spacer is needed.
What across-flats size should I specify?
A standard wrench size. Across-flats is the distance between two opposite flat faces of the hexagon — a standoff with an A/F of 7 mm takes a 7 mm wrench; an A/F of 6.8 mm takes nothing properly. State the A/F as a standard size and check it against the wrench that will be used.
Can a standoff have different threads on each end?
Yes — for example an M3 female thread on one end and an M3 male thread on the other — and the drawing must say so for each end. State diameter, pitch, class and depth per end, and the torque the joint must survive, so the engagement can be confirmed: a female thread too shallow will strip under torque, and a male thread too short will not engage enough of the mating thread.
Common pitfalls and how to avoid them
The most common pitfall is specifying the length without the stack-up. A spacer that is right on its own can be wrong in a stack of five. State the stack-up requirement.
The second is an across-flats dimension that matches no wrench. State a standard A/F size, and check it against the wrench that will be used.
The third is a thread configuration stated for one end only. A standoff has two ends, and each needs its own thread callout. State both.
The fourth is a female thread too shallow for the torque. State the thread depth and the torque, so the engagement can be confirmed.
The fifth is ordering spacers as loose parts when they belong to a kit. State the kit and the labelling requirement in the RFQ, so the parts arrive ready to use.
The sixth is forgetting the bore fit on a sleeve. A sleeve that must slide on a shaft needs a stated fit, not just a bore size. State the fit — H7/g6 or H7/h6 — alongside the bore.

The stack-up check: a worked example from this post
The arithmetic is the post’s own, and it is worth doing before the drawing goes out:
- One spacer at ±0.05 mm length tolerance is small.
- Five of them in one assembly can stack to ±0.25 mm of variation — enough to misalign a board or a panel.
The check: count the spacers in the stack, multiply the individual length tolerance, and compare the total against the alignment the assembly allows. If the total is too large, the fix is a tighter length tolerance on each spacer or a stated stack-up requirement in the RFQ — not a looser assembly. The drawing governs, and the stack-up is the buyer’s responsibility to state.
The same logic applies to the bore fit: state the fit, not just the bore size. A sleeve that must slide on a shaft needs a stated fit — typically H7/g6 or H7/h6 to ISO 286, as stated on the bushings page — so the supplier can confirm the pair.
Buyer checklist
- The part type is named: sleeve, spacer, or hex standoff — and the critical dimension for that type is identified.
- For a sleeve, the bore, outside diameter, and fit are stated.
- For a spacer, the length is stated, and the stack-up requirement for the assembly is stated.
- For a hex standoff, the across-flats dimension is a standard wrench size.
- The thread configuration is stated for each end separately, with diameter, pitch, class, and depth.
- The torque the joint must survive is stated, so thread engagement can be confirmed.
- The material and finish are stated per part, matching its visibility and environment.
- The quantity, kit, and labelling requirements are stated, so the parts arrive ready to use.
Send the drawing and state the type, the critical dimension, and the assembly the part belongs to in the RFQ at https://precimora.com/request-a-quote/ — the quote is promised in 24–48h.