Brass is Precimora’s default material, and for good reason: it machines beautifully, it holds a tight tolerance, and it resists corrosion in most services. But brass is not always the right choice. Aluminum is lighter, it is often cheaper, and for some parts it is the better material — a housing that must be light, a part that must dissipate heat, a component where the weight matters more than the wear resistance. Choosing aluminum over brass is not a downgrade. It is a decision that follows from what the part must do, and it needs to be made deliberately, with the trade-offs understood.

Weight: the reason most buyers switch
Aluminum is roughly a third the weight of brass. That is the single biggest reason to choose it, and it matters wherever the part is carried, moved, or mounted on something that moves. A handheld device, a drone component, a part on a vehicle, a housing that an installer lifts into place — in all of these, the weight of the part is a cost, and aluminum cuts it by two-thirds.
The weight saving is not free. Aluminum is softer than brass, so it wears faster where it rubs, and it is weaker, so a wall that is strong enough in brass may need to be thicker in aluminum. The trade-off is real: the part gets lighter, but it may need to be larger to carry the same load. State the weight constraint in the RFQ — the maximum weight, or the reason weight matters — and the supplier can confirm whether aluminum can meet the strength requirement at the weight the buyer needs.
Cost: cheaper material, different machining
Aluminum is generally cheaper than brass as a material, and it machines faster — it cuts easily, it produces long, stringy chips that need to be managed, and it can be cut at higher speeds. That sounds like a cost saving, and it often is, but the saving is not automatic. Aluminum’s softness means it is easily scratched and easily dented, so it needs more careful handling and packing. It also needs a different surface treatment: bare aluminum oxidises, and a part that must resist corrosion needs anodising or another finish, which adds a step that brass does not need.
State the quantity and the finish in the RFQ, so the cost comparison is honest. A small batch of aluminum parts with an anodised finish may cost more than the same parts in brass with no finish, because the anodising step costs more than the material saving. A large batch where the material saving dominates will be cheaper in aluminum. The supplier can give the comparison, but only if the finish and the quantity are stated.
Machining: fast, but with its own problems
Aluminum machines fast, and that speed is its advantage. But it brings problems that brass does not have. The chips are long and stringy, and they can wrap around the tool or the workpiece if they are not cleared. The material is soft, so a dull tool will smear it rather than cut it, leaving a poor surface. And aluminum expands more with heat than brass does, so a part machined hot will measure differently when it cools — the temperature of the part during machining matters more for aluminum than for brass.
These are the supplier’s problems, not the buyer’s, but the buyer should know that an aluminum part needs a different machining approach, and that the surface finish and the tolerance must be confirmed for aluminum specifically. A tolerance of ±0.05 mm that is routine in brass may need a different approach in aluminum, because the material moves more with temperature. State the tolerance on the drawing, and ask the supplier to confirm it for aluminum in the engineering review.

Strength and wear: where aluminum loses
Aluminum is weaker and softer than brass, and that is the trade-off that decides most choices. A part that must carry a load, resist wear, or hold a thread under repeated assembly will last longer in brass. A thread in aluminum is easily stripped if it is assembled and disassembled repeatedly, because the soft material cannot take the repeated loading. A bearing surface in aluminum will wear faster than the same surface in brass or bronze.
Where the part must be strong or wear-resistant, the choice is not aluminum versus brass — it is aluminum with a design change versus brass as drawn. A thicker wall, a larger diameter, or a steel insert for the thread can make an aluminum part strong enough, but each of those changes the part. State the load and the wear requirement in the RFQ, and the supplier can confirm whether aluminum can meet it, or whether the part needs a design change or a different material. The companion post on brass versus bronze covers the wear question for bronze; for aluminum, the rule is the same — the load and the wear decide the material, not the weight alone.
Corrosion: aluminum protects itself, but not everywhere
Aluminum forms a thin oxide layer on its surface that protects it from further corrosion, and in many environments that is enough. But aluminum corrodes where it is in contact with a dissimilar metal — a steel screw in an aluminum part, for example — because the two metals form a galvanic cell, and the aluminum corrodes. It also corrodes in salt water and in some chemicals, where brass would survive.
State the environment in the RFQ: whether the part will be in contact with steel, whether it will see salt water, and what chemicals it will meet. If the part needs a protective finish, state the finish — anodising is the usual choice for aluminum, and it should be confirmed with the supplier, because Precimora’s published finishes are for brass and the finish for aluminum must be agreed in the review. A part specified without the environment will be delivered bare, and bare aluminum in the wrong environment will corrode.
When aluminum is the right choice
Aluminum is the right choice where the weight matters more than the wear, where the part does not carry a heavy load, where the part must dissipate heat, or where the cost saving at the stated quantity is real. It is the wrong choice where the part must resist wear, hold a thread under repeated assembly, or survive a corrosive environment without a protective finish.
The decision should be made with the supplier, in the engineering review, with the weight, the load, the wear, the environment, and the finish all stated. A buyer who states all five will get a recommendation that is based on the part, not on the material. A buyer who states only the weight will get aluminum, whether or not it is the right choice.

Common pitfalls and how to avoid them
The most common pitfall is choosing aluminum for weight and forgetting the wear, so the part wears out quickly. State the load and the wear requirement, not just the weight.
The second is a thread in aluminum that is assembled repeatedly and strips. Use a steel insert for a thread that will be assembled repeatedly, or choose brass.
The third is aluminum in contact with steel, where galvanic corrosion eats the aluminum. State the mating materials and the environment.
The fourth is an anodised finish assumed but not stated, so the part arrives bare. State the finish in the RFQ.
The fifth is a tolerance copied from a brass part without confirming it for aluminum, where thermal expansion moves the part. Ask the supplier to confirm the tolerance for aluminum.
Buyer checklist
- The reason for choosing aluminum is stated: weight, cost, heat, or another specific requirement.
- The load and the wear requirement are stated, so the supplier can confirm aluminum can meet them.
- The quantity and the finish are stated, so the cost comparison is honest.
- The environment is stated: contact with steel, salt water, chemicals.
- Threads that will be assembled repeatedly are flagged for a steel insert or a different material.
- The finish — bare, anodised, or another — is stated in the RFQ.
- The tolerance is confirmed for aluminum, with thermal expansion in mind.
- The supplier has confirmed the material choice in the engineering review, with the weight, load, wear, environment, and finish all stated.