
Brass is the default material for plumbing and HVAC fittings for a reason: it machines cleanly, it resists corrosion in water, it takes a thread well, and it lasts. But a brass turned part for water service is not the same as a brass turned part for a dry assembly. Water changes the rules. It brings dezincification, it brings lead regulations, it brings pressure and temperature, and it brings a thread standard that must match the rest of the system. A plumbing fitting specified like a general turned part will be quoted correctly and fail in service. A plumbing fitting specified with its service in mind will be quoted with the right alloy, the right thread, and the right compliance.
Water service changes the alloy choice
The first question for a plumbing part is what water it will see. Cold water, hot water, drinking water, and heating-system water are four different services, and they do not all suit the same brass. The companion post on dezincification explains the mechanism: in aggressive water, zinc is leached out of the brass, leaving a weak, porous structure that can fail without warning. The companion post on lead-free brass and compliance explains the regulation: drinking-water applications require lead-free brass, and the compliance route must be stated in the RFQ.
For a plumbing or HVAC fitting, state the service in the RFQ: drinking water or not, hot or cold, and the market it will be sold in. The alloy follows from the service. A dezincification-resistant brass, such as CW602N, is the usual choice where the water is aggressive; a lead-free brass, such as CW724R or C69300, is the usual choice where the water is for drinking. Both are standard grade examples to confirm with the supplier, not stocked grades — the supplier confirms the grade against the service and the market. A part specified without the service will be quoted in the standard free-cutting brass, CW614N or C36000, which is the right choice for a dry assembly and the wrong choice for aggressive water.

Threads: the standard the rest of the system uses
A plumbing fitting lives or dies by its thread, because the thread must match the pipe, the valve, or the fixture it connects to. The thread standard for plumbing is set by the market, not by the part: a fitting for the European market uses a different thread from a fitting for the American market, and a fitting for a gas system uses a different thread from a fitting for a water system. Precimora’s published capability is metric threads to ISO 261 (internal 6H, external 6g), with UNC and UNF on request — but a plumbing fitting’s thread is usually a pipe thread, not a metric fastener thread, and the pipe thread standard must be stated explicitly.
State the thread standard on the drawing, in full: the standard, the size, and whether the thread is parallel or tapered. A tapered pipe thread seals by wedging into the mating thread; a parallel pipe thread seals with a washer or an O-ring. The two are not interchangeable, and a part with the wrong one will not seal. If the thread standard is not known, state the mating part it must connect to, and the supplier can confirm the standard in the engineering review. The companion post on thread specification covers the general rules; for plumbing, the rule is that the market and the mating part decide the thread, and the drawing must name it.
Pressure and temperature: state the service, not the rating
A plumbing fitting sees pressure and temperature, and the buyer should state both — not as a rating the part must achieve, but as the service the part will see. The maximum working pressure and the maximum temperature are the inputs the supplier needs to confirm the wall thickness, the thread engagement, and the alloy. A fitting for a cold-water line sees a different service from a fitting for a hot-water heating circuit, and the difference is not just the temperature: hot water accelerates dezincification, so a hot-water fitting needs a more resistant alloy than a cold-water fitting in the same water.
State the pressure and the temperature in the RFQ, as the service conditions, not as a test requirement. Do not invent a pressure rating or a test pressure — the supplier confirms what the part can take, and the buyer states what it will see. If the fitting must pass a specific test — a pressure test at a stated multiple of the working pressure, for example — state the test, and the supplier can confirm whether it is included in the inspection plan.
Sealing: how the fitting actually seals
A plumbing fitting seals in one of three ways: a tapered thread that wedges, a parallel thread with a washer or an O-ring, or a compression fitting that squeezes a ferrule onto the pipe. The sealing method decides the geometry of the part: a tapered thread needs a thread that runs to a specific length; a washer seal needs a flat face of a specific size; a compression fitting needs a seat of a specific angle. The drawing must show the sealing feature, and the RFQ must say which method the fitting uses.
The O-ring groove post covers the groove in detail; for a plumbing fitting with an O-ring seal, the groove and the sealing face are the critical features, and the face finish should be in the smoother part of the published range. For a washer seal, the flat face must be flat and smooth enough for the washer to conform to it, and the face should be called out on the drawing. For a tapered thread, the thread itself is the seal, and the thread quality — the finish, the profile, the engagement length — is what decides whether it seals.

Surface finish and plating for water service
A plumbing fitting’s surface finish matters for two reasons: the sealing face must be smooth enough to seal, and the outside must resist the water and the environment it sits in. A nickel-plated finish, typically 5–25 µm as published, protects the brass and gives a clean appearance, and it is the usual choice for a visible fitting. But plating must be confirmed for the service: a plating that is fine for a dry assembly may not suit continuous water contact, and the plating thickness and the base material must be confirmed together.
State the finish in the RFQ — as-machined, polished, or plated — and state the service it must survive. If the fitting will be visible, say so, because the appearance requirement changes the finish. If the fitting will be hidden inside a wall or a cabinet, the appearance matters less, and the finish can be chosen for corrosion resistance alone.
Compliance: the paperwork that travels with the part
A plumbing fitting for drinking water must comply with the lead regulations of the market it is sold in, and the compliance requirement must be stated in the RFQ. The companion post on lead-free brass and compliance covers the regulations in detail; for a plumbing fitting, the practical points are: state the market, state the regulation, and ask the supplier to confirm the alloy and the documentation. The documentation — a material certificate, a declaration of conformity, or a test report — should be agreed in the RFQ, because it is part of the inspection documentation that Precimora configures per project.
A fitting for a non-drinking-water application — a heating circuit, a cooling line, an industrial water line — may not need the same compliance, but the service should still be stated, because it decides the alloy. A heating-system fitting in aggressive water needs a dezincification-resistant alloy whether or not it is for drinking water, and the only way the supplier knows is if the service is stated.
Common pitfalls and how to avoid them
The most common pitfall is specifying a plumbing fitting in standard free-cutting brass without stating the water service, so the alloy is wrong for the water. State the service — drinking or not, hot or cold, and the market.
The second is a thread specified as a metric fastener thread when the system uses a pipe thread. State the pipe thread standard in full, including whether it is parallel or tapered.
The third is a sealing face that is too rough for the washer or the O-ring to conform to. Call out the sealing face and give it a smooth finish.
The fourth is a pressure or temperature rating invented by the buyer. State the service conditions, and let the supplier confirm what the part can take.
The fifth is a compliance requirement left unstated, so the part arrives without the documentation the market needs. State the market, the regulation, and the documentation in the RFQ.
Buyer checklist
- The service is stated: drinking water or not, hot or cold, and the market.
- The alloy follows from the service: dezincification-resistant or lead-free where the service demands it.
- The thread standard is stated in full: standard, size, parallel or tapered.
- The sealing method is stated: tapered thread, washer, O-ring, or compression.
- The sealing face is called out on the drawing, with a smooth finish.
- The pressure and temperature are stated as service conditions, not invented ratings.
- The finish — as-machined, polished, or plated — is stated, with the service it must survive.
- The compliance requirement and the documentation are stated in the RFQ.