A brass turned part is rarely ordered as just “brass.” The alloy family behind that word decides how the part machines, how it behaves in service, and how it is quoted. A buyer who names a brass alloy with a reason — rather than writing “brass” and leaving the choice to the supplier — gets a faster quote, a part that is more likely to work the first time, and a price that reflects the real material rather than a guess. The choice is not about finding the single best alloy. It is about matching the alloy to the job the part has to do.

Why the alloy matters more than the word “brass”
Brass is a family of copper-zinc alloys, and the members of that family differ in real ways. Some machine very cleanly and are the default for small turned fittings. Others are stronger but slower to machine. Some are made for cold working, some for hot forging, and some for a specific service condition such as contact with water. When an RFQ says only “brass,” the supplier has to assume an alloy, and that assumption may not match the one the designer had in mind. If the assumption is wrong, the part may machine well but fail in service, or serve well but cost far more than it needed to. Naming the alloy family — or at least naming the service conditions and asking for a recommendation — removes that guesswork. A drawing that was copied from an earlier part may carry an alloy that was right for that part and wrong for this one, so the alloy should be checked as deliberately as any dimension.
Machinability: the alloy that cuts cleanly
Machinability is usually the first practical difference a buyer notices, because it drives cycle time and therefore a large part of the quote. Free-machining brass alloys, the ones with a small amount of lead added, cut cleanly, break chips well, and allow high turning speeds with a good surface. That is why they are the default for many small turned fittings, nuts, bushings and connectors. The trade-off is that the same addition that makes the alloy easy to machine is the one that some applications restrict. A buyer should ask two questions: how complex is the part, and how much machining does it actually need? A simple turned fitting with a thread and a bore is well served by a free-machining alloy. A part with thin walls, deep bores, or fine features benefits even more from one, because a gummy or hard-to-machine material will show its problems exactly on those features. If the part is simple and the quantity is large, machinability is where most of the cost difference between alloys will appear.
Corrosion and service environment: where the part will live
The second driver is the environment. A fitting that sits indoors in a dry assembly faces very different conditions from one that carries water, sits outdoors, or is exposed to cleaning chemicals. Some brass alloys are chosen specifically for resistance to dezincification — the selective loss of zinc in water service that can weaken a fitting over time. Others are chosen for general corrosion resistance in ordinary indoor and sheltered outdoor use. A buyer should name the environment in the RFQ in plain words — indoor, sheltered outdoor, water contact, marine, chemical washdown — rather than writing “corrosion resistant” and leaving the supplier to guess. If the part will sit against another metal, say so, because galvanic contact between dissimilar metals is a real design consideration and the alloy choice should be made together with the mating material, not in isolation. Appearance matters too: an alloy that tarnishes or discolours in service may be fine for a hidden fitting and unacceptable for a visible one.

Strength and wear: what the part must carry
Brass alloys also differ in strength and wear resistance. A fitting that is tightened once and left alone needs less strength than a fastener that is cycled repeatedly, a part that carries a load in tension, or a component that sees vibration. Some brass families are stronger and harder, and they earn their place where the part must resist deformation or wear in sliding contact. Others are softer and more ductile, and they suit parts that are formed, pressed, or crimped after turning. The buyer does not need to quote strength figures from a datasheet. The buyer needs to describe the load in plain terms: is the part tightened once, cycled repeatedly, loaded in tension, pressed into a housing, or subject to vibration? That description lets the engineer judge whether the alloy is adequate, and it is more useful than a grade name copied without context. A thread that must survive repeated assembly needs an alloy that holds a thread; a thin wall needs an alloy that will not deform when it is tightened.
Lead-free requirements: the rule that overrides the rest
For some applications, the alloy choice is not a trade-off at all — it is a rule. Drinking-water fittings, food-contact parts, and products sold into markets with lead restrictions may require a lead-free or low-lead brass alloy. Lead-free alloys machine differently from the free-machining leaded alloys they replace: they can be harder on tooling, slower to turn, and more sensitive to cutting conditions, and that difference shows up in the quote. A buyer who needs a lead-free alloy should say so explicitly in the RFQ, and should say which regulation or customer requirement drives it, rather than assuming the supplier will infer it from the application. Do not assume a leaded alloy is acceptable because the part looks like a standard fitting, and do not assume a lead-free alloy is a drop-in substitute with the same price. If the requirement is uncertain, ask the customer or the end-use standard first, and state the answer in the RFQ. Getting this wrong is not a cost problem — it is a compliance problem that can only be fixed by remaking the parts.
How to state the alloy in your RFQ
A good alloy line in an RFQ does more than name a grade. It names the alloy family, the service environment, the load, and any regulatory requirement, and it says whether the alloy is a firm requirement or open to recommendation. If the drawing already specifies an alloy, check whether that specification is a requirement or a habit carried over from an earlier part. If you are unsure between two alloys, say so in the RFQ and ask for a recommendation — an engineer who sees the whole application can advise, but only if the application is described. State the mating material, whether the part is tightened once or repeatedly, and whether appearance matters. A short note such as “alloy is open to recommendation for this environment” can save a redesign later, provided the environment is actually described. The worst RFQ line is a single word — “brass” — with no environment, no load, and no requirement attached to it.
Common pitfalls and how to avoid them
The most common pitfall is copying an alloy from a similar part without checking the environment, so a fitting that worked indoors fails in water service. The second is choosing a free-machining leaded alloy for a drinking-water or food-contact application, where a lead-free alloy was required. The third is specifying an alloy by a trade name or a grade that is not available in the required form, which delays the quote while the grade is clarified. The fourth is changing the alloy after the quote without re-quoting, which leaves the price, the process, and the inspection out of step with the drawing. The fifth is assuming that a stronger alloy is always better, and paying for strength the part never uses. The sixth is leaving the alloy choice to the supplier without describing the application, so the supplier has to guess the service conditions. Each of these is avoided by writing the environment, the load, and the requirement into the RFQ before the quote is requested.

Buyer checklist
- Name the service environment: indoor, sheltered outdoor, water contact, marine, chemical, or washdown.
- Name the failure mode you are designing against: corrosion, dezincification, wear, thread damage, or load.
- State whether a lead-free or low-lead alloy is required, and which regulation or customer requirement drives it.
- Describe the load: tightened once, cycled repeatedly, tension, press fit, or vibration.
- State the mating material and whether the joint is assembled once or repeatedly.
- Say whether appearance and tarnishing matter in service.
- Check whether the alloy on the drawing is a requirement or a habit from an earlier part.
- If unsure between two alloys, say so in the RFQ and ask for a recommendation, with the application described.