Turning produces the round form of a part, but many turned parts need more than turning before they are finished. A cross hole, a flat, a knurled grip, a clean edge, or a rolled thread each comes from a secondary operation — a step after the lathe — and each one needs to be specified in the RFQ if it is to be quoted correctly the first time. A buyer who understands what each operation does, and what information it needs, avoids the two most common problems with secondary work: an operation that was never quoted and appears later as an extra charge, and an operation that was quoted on a guess and turns out to be the wrong one.
Drilling and cross holes: what the hole must do
Drilling after turning usually means a hole that the lathe cannot make in the same setup — a cross hole through the side of a part, an off-centre hole, or a hole at an angle. The buyer should specify the hole diameter, its depth, its position relative to a turned feature, and whether it is a through hole or a blind hole. Position matters: a cross hole that must line up with another feature needs a positional reference, and a hole that is only for weight reduction or drainage can carry a looser position. The hole’s function should also be stated — is it for a pin, a screw, a wire, or fluid? — because that decides whether the hole needs a clean entry and exit, a chamfer, or a particular surface condition. A hole that is drilled after turning can leave a burr where it breaks through, so deburring of the hole should be considered at the same time. If the drawing shows the hole but the RFQ does not mention it, the supplier may quote the turned form only, and the drilling will surface later as an addition.

Milling: flats, slots, and features the lathe cannot make
Milling adds the features that are not round: flats for a wrench, slots, keyways, steps, or a hexagonal form on part of a turned part. The buyer should specify the milled feature’s size, its position relative to the turned axis, and the surface it must present — a wrench flat needs two parallel faces at a stated distance apart, while a slot needs a width, a depth, and a length. Tolerances on milled features should follow the same discipline as on turned dimensions: tight only where the function needs it, and looser where it does not. The orientation of a milled feature relative to another feature should be stated where it matters, for example where a flat must line up with a cross hole. Milling is often done in a second setup, so it adds handling and setup time; a part with several milled features in different orientations will cost more than one with a single flat, and the RFQ should show all of them so the supplier can quote the full sequence rather than discovering one later.

Knurling: grip, press fit, and appearance
Knurling presses a diamond or straight pattern into the surface of a turned part, and it is used for three different reasons that should not be confused. The first is grip: a knurled knob, handle, or adjustment screw that must be turned by hand. The second is a press fit: a knurled outside that grips the parent material and resists pull-out and rotation. The third is appearance: a decorative pattern on a visible part. The buyer should state which reason applies, because each one drives a different knurl: a grip knurl needs a pattern that is comfortable and effective by hand, a press-fit knurl needs a pattern and a size that match the hole it will sit in, and a decorative knurl needs a consistent, clean pattern. Specify the knurl type, the length of the knurled section, and where it starts and ends relative to a turned feature. A knurl that runs into a thread or a sealing face will cause problems, so its position should be defined on the drawing. If the knurl is for a press fit, state the parent material and the hole size, because the knurl and the hole are specified together, not separately.

Deburring and edge finishing: the step that is easy to forget
Every machining operation leaves an edge, and deburring is the step that makes that edge safe and functional. A sharp edge can cut a hand, damage a seal, prevent assembly, or break off in service and become debris. The buyer should state the edge requirement in the RFQ rather than assuming it: are the edges to be broken lightly, chamfered to a stated size, or fully rounded? Which edges matter — all of them, or only the ones that are handled or that meet a seal? A chamfer on a thread entry helps assembly; a sharp edge on a press-fit diameter can shave material from the mating part. Deburring is often treated as a minor step, but on a part with many features it takes real time, and a quote that does not include it will either leave sharp edges or add the work later. State the requirement plainly, and check the first parts on arrival for the edges that matter most. A part that is perfect in every dimension but sharp enough to cut is not a finished part.
Thread rolling: strong threads without cutting
Thread rolling forms a thread by pressing it into the part rather than cutting it away, and it is used where a strong, clean thread is needed on a turned part. Rolled threads can be stronger than cut threads because the material is displaced rather than removed, and they often have a better surface. The buyer should specify the thread size, the length of the threaded section, and whether the thread is external or internal — rolling is normally an external-thread process. The material matters: some alloys roll well and others do not, so the alloy and the thread should be considered together. The thread’s function should be stated — is it tightened once, cycled repeatedly, or mated with a specific standard thread? — because that decides the thread class and the inspection. A rolled thread needs a prepared diameter before rolling, so the turning and the rolling are one sequence, not two independent operations. If the RFQ asks for a thread without saying how it should be made, the supplier will choose the method; if the application needs a rolled thread, say so, and say why.
How to specify secondary operations in the RFQ
The rule for secondary operations is simple: show every operation on the drawing, and name every operation in the RFQ. A drawing that shows a cross hole, a flat, and a knurl, but an RFQ that mentions only “turned part,” will be quoted as a turned part. List each secondary operation, the feature it creates, and the requirement that applies to it — position, size, surface, and function. State the sequence where it matters: a hole drilled before a thread is rolled behaves differently from one drilled after. State the inspection for secondary features as well as for turned ones: which cross hole position is checked, which flat distance is measured, which knurl is inspected. If a secondary operation is optional, say so, and ask for it to be quoted separately so the buyer can decide with a price in front of them. A complete RFQ is one where the supplier does not have to guess which operations are included.
Common pitfalls and how to avoid them
The most common pitfall is showing a secondary feature on the drawing but never mentioning it in the RFQ, so it is not quoted and appears later as an extra charge. The second is specifying a knurl without saying whether it is for grip, press fit, or appearance, so the wrong pattern is produced. The third is forgetting deburring, and receiving parts with sharp edges that cannot be assembled or handled safely. The fourth is a milled flat or slot whose orientation relative to another feature was never stated, so it is machined in the wrong position. The fifth is asking for a rolled thread without checking whether the alloy rolls well, or without stating the thread’s function. The sixth is inspecting only the turned dimensions on arrival and never checking the secondary features, so a misplaced cross hole or a missing chamfer is discovered only in assembly. Each of these is avoided by listing every secondary operation in the RFQ, with its feature, its position, and its function stated plainly.
Buyer checklist
- List every secondary operation the part needs: drilling, milling, knurling, deburring, thread rolling, and any other.
- For each drilled hole, state diameter, depth, position, through or blind, and function.
- For each milled feature, state size, position relative to the turned axis, and orientation where it matters.
- For each knurl, state whether it is for grip, press fit, or appearance, plus type, length, and position.
- State the edge requirement: lightly broken, chamfered, or rounded — and which edges it applies to.
- For a rolled thread, state thread size, length, function, and whether rolling is required.
- Ask for secondary operations to be quoted with the turning, not discovered afterwards; quote optional ones separately.
- Agree which secondary features are inspected on arrival, and how — position, flat distance, knurl, and edges.